pe給水管的翻邊是什么？翻邊高度不一致怎么處理？如何處理翻邊？  

pe給水管的翻邊是管道焊接過程中擠壓成形的，通常稱為內翻邊和外翻邊。翻邊質量也影響pe給水管道的流動效率。如果翻邊過大，容易產生結垢，導致管道內微生物生長。二是在排水工程中，會產生泥沙淤積，降低水流效率。一般來說，這是由于pe管材端口不平整，受熱面積不均勻，必須重新熔化造成的。在以往的pe給水管施工中，暫時沒有很好的方法來處理內翻邊問題，這里總結了PE管翻邊不合格的幾個原因：翻邊過小：吸熱時間不足或焊接機座行程不足；翻邊過大：吸熱時間過長，PE給水管原材料熔化過多；翻邊錯位：PE管未用水固定，或聚乙烯管熔口切割不順；         

pe給水管變形檢測與控制方法質量由每一個小細節決定。因此，本文根據自己的工作經驗，結合他人的經驗，總結了給排水用聚乙烯管施工中不應出現的問題，詳細分析了原因，并提出了解決辦法。        pe給水管道變形檢測應在管道覆土夯實后進行，并在施工過程中進行。施工變形，即短期展平率的試驗次數，一般應滿足以下要求：每一施工段最初50米不少于3次，并在點處進行管軸垂直裂縫縱橫直徑的表面測量；相同條件下每100米不少于3次，取起點、中點、接近終點進行檢測，在地質條件下，當采用填料和壓力時，如有變化應測量實際工藝和管徑，重復上述檢測內容。對于允許的短期（24小時）壓扁率，HDPE大直徑塑料管的施工變形是實測的短期壓扁率應＜4%。